How To Jack Up A Car Without A Jack?

Every car owner must know how to jack up a car without a jack, but what if you don’t have a jack with you? In this article, we will be going over some of the basics of how to jack up a car without a jack.

You could feel powerless if you’ve ever needed to change a tyre or safely operate underneath a car but haven’t got a car jack. Fortunately, there are a few techniques you can use to move your car without a jack. Using a jack has a lot of dangers and has resulted in fatalities and serious injuries.

Jack stands substitutes:

Compared to jack stands, the following automobile lift solutions are significantly safer:

Mini ramps:

Similar to jack stands, small ramps are affordable. They are short ramps made to lift your car’s front end by its tyres. Mini ramps have a few limitations while being a suitable option for simple auto repairs like oil changes. Mini ramps, for instance, don’t offer enough lift height. Since they are only six inches tall, they cannot raise a person’s body enough to allow them to safely slide underneath the car. Mini ramps also only actually support 2 wheels at once.

A 2-post post or 4-post post lift of the commercial type:

If you’re going to purchase a lift, the grade of the commercial is the best option. While not significantly more expensive than a less expensive “entry-level” lift, the commercial quality lift provides significantly greater durability and safety. Sadly, every 2-post and 4-post lift has a sizable footprint. You would need a ceiling height of 12′ or higher and a width of around 1.5 garage spaces to be able to accommodate one inside your garage. They also need concrete that is thicker than usual and certified for 3,000 PSI. The majority of home garages need to be upgraded.

The Kwik-Lift:

The Kwik-Lift is the last, although by no means least, option. Discover why it’s the greatest jack stand substitute by reading on.

How can a car be raised without a jack?

Utilizing natural incline:

You don’t need a jack if there are raised ramps nearby, or even if the footpath curbs are in an urban area.

How To Jack Up A Car Without A Jack?

To gain the appropriate height to operate beneath the automobile, drive your vehicle at such an angle to the ramps so that one of its wheels is raised.

You can either pull onto the ramp in reverse at an angle to elevate the front wheels, or you may drive upward at an angle to elevate the back wheels.

Removing soil from below of car:

Going off-road when the ground isn’t really solid is an additional option.

  • As normal, engage the emergency brakes, park your automobile, and chock the wheels.
  • You can create the appropriate elevation for changing a tyre by digging a hole underneath the tyre.
  • The earth may be dug readily for this purpose using a shovel.
  • Dig continuously until the axle is firmly supported by the obstructions.

This will enable you to attain a suitable elevation for simple tyre removal. Replace your tyre after removing the lug nuts.

Using woods or bricks pieces:

Using pieces of raw, natural wood can be used to lift the car high enough to allow access beneath it without the need for a jack.

These parts can be stacked to create a wooden block. When stacking the planks, stay away from nails.

The reason is also that nails cause the hardwood planks to crack and leave a weak spot in the middle, which increases the likelihood that the entire block would collapse when the automobile is parked on it.

You can either manually push the automobile onto the block of wood or drive it up to the desired elevation for a tyre change.

You may lift your automobile up similarly using bricks or some other flat rock pieces. Use blocking or supporting item, such as bricks or a wooden board, using caution to prevent the tyre from slipping off the platform you’ve built.

Important Safety Advice:

After raising the automobile, use your handbrake or block the wheels to prevent them from rolling. It is suggested that you use both strategies. Applying the chock must be done on the side that is not being lifted. People have died after being smashed by their cars while working underneath them, thus we urge particular caution in following all safety rules.


In conclusion, there are several alternatives to using a conventional auto jack while lifting your vehicle.

You can lift 1 side of your car by using slopes, naturally elevated locations, and the curbs of walkways as ramps. To get the required height for tyre replacement, you can even use a shovel and your bare hands to dig in the soil beneath the tyre.

Or, if none of these options is available, you can construct your own ramp out of flat pieces of stone, brick, or wood to provide you with the necessary room to operate underneath a car. Always take the required safety procedures to ward off any potential fatalities.


Why is there no jack in my car?

The lack of a spare tyre and jack in vehicles is due to manufacturers’ desire for lighter, more fuel-efficient cars.

To replace a tyre, do I require a jack stand?

Yes, changing a tyre probably only requires one jack stand, but it’s not ideal to repeatedly flex the frame in that way, especially on a unibody car. The home mechanic can change tyres and safely raise a vehicle from either the side or the end by using two jack stands.

Is a jack usable without jack stands?

If you need to get a tyre changed and are stuck or don’t have jack stands, you can use a jack alone, but you must take caution. Never ever put your hands or feet immediately underneath the car, and also finish any tasks you begin as soon as you can.

Without a jack, how do you replace a tyre?

Dig out the dirt surrounding and beneath the flat tyre with a shovel or your hands in a real emergency. Once you have enough space to change the tyre, continue digging. Once more, remove the lug nuts, switch the tyres, install the new lug nuts, and then gradually tighten. Until you’re able to drive out of the hole, fill it in.

Leave a Comment